{"id":69,"date":"2019-05-31T23:14:18","date_gmt":"2019-06-01T03:14:18","guid":{"rendered":"https:\/\/openstudio.pub\/techwriting\/chapter\/project-completion-student-sample-welding\/"},"modified":"2025-04-14T08:08:00","modified_gmt":"2025-04-14T12:08:00","slug":"project-completion-student-sample-welding","status":"publish","type":"chapter","link":"https:\/\/openstudio.pub\/techwriting\/chapter\/project-completion-student-sample-welding\/","title":{"raw":"Project Completion Student Sample - Welding","rendered":"Project Completion Student Sample – Welding"},"content":{"raw":"Work Completion Form <\/strong>\n\nCustomer: <\/strong>In house safety improvement project.\n\nWork order title:<\/strong>  L Brackets\n\nWork order number:<\/strong> LB-722701\n\nWork order cost:<\/strong> $853.00 or $8.53 per part Cost includes materials only.\n\nStart date:<\/strong> 02.13.27            Completion date:<\/strong> 02.20.17 Instruction:  <\/strong>\n\nCreate 100 L Brackets following the specifications given on the part diagram provided below. Measurements given in mm. Each part must be tested once completed to ensure load capacity of 50lbs minimum is achievable as these will be installed in a cable guide system. Minimum requirements per OSHA guidelines.\n\n\"\"\n\nSteps: <\/strong>\n
    \n \t
  1. Cut \u00bc\u201d flat stock and heat mold to create bracket shape with angle at a radius of 10mm.<\/li>\n \t
  2. Drill out cable hole at a diameter of 20mm and install insulating rubber seal.<\/li>\n \t
  3. Drill out mounting hole x2 at a diameter of 10mm.<\/li>\n \t
  4. Clean all cut or drilled edges to ensure no burrs or sharp edges remain.<\/li>\n \t
  5. Test part for minimum weight requirements.<\/li>\n \t
  6. Package in 20 piece units for maintenance crew and store in part building aisle B section LB-722701.<\/li>\n \t
  7. Enter into parts inventory.<\/li>\n \t
  8. Return this form to maintenance office.<\/li>\n<\/ol>\n <\/strong>\n\nDate of completion:<\/strong> 02.20.17\n\nInspected by:<\/strong> J. Jones\n\nWork completed by: <\/strong>J. Jones\n\nWork completion signed off by:<\/strong> Maintenance Manager","rendered":"

    Work Completion Form <\/strong><\/p>\n

    Customer: <\/strong>In house safety improvement project.<\/p>\n

    Work order title:<\/strong>  L Brackets<\/p>\n

    Work order number:<\/strong> LB-722701<\/p>\n

    Work order cost:<\/strong> $853.00 or $8.53 per part Cost includes materials only.<\/p>\n

    Start date:<\/strong> 02.13.27            Completion date:<\/strong> 02.20.17 Instruction:  <\/strong><\/p>\n

    Create 100 L Brackets following the specifications given on the part diagram provided below. Measurements given in mm. Each part must be tested once completed to ensure load capacity of 50lbs minimum is achievable as these will be installed in a cable guide system. Minimum requirements per OSHA guidelines.<\/p>\n

    \"\"<\/p>\n

    Steps: <\/strong><\/p>\n

      \n
    1. Cut \u00bc\u201d flat stock and heat mold to create bracket shape with angle at a radius of 10mm.<\/li>\n
    2. Drill out cable hole at a diameter of 20mm and install insulating rubber seal.<\/li>\n
    3. Drill out mounting hole x2 at a diameter of 10mm.<\/li>\n
    4. Clean all cut or drilled edges to ensure no burrs or sharp edges remain.<\/li>\n
    5. Test part for minimum weight requirements.<\/li>\n
    6. Package in 20 piece units for maintenance crew and store in part building aisle B section LB-722701.<\/li>\n
    7. Enter into parts inventory.<\/li>\n
    8. Return this form to maintenance office.<\/li>\n<\/ol>\n

       <\/strong><\/p>\n

      Date of completion:<\/strong> 02.20.17<\/p>\n

      Inspected by:<\/strong> J. Jones<\/p>\n

      Work completed by: <\/strong>J. Jones<\/p>\n

      Work completion signed off by:<\/strong> Maintenance Manager<\/p>\n","protected":false},"author":1,"menu_order":3,"template":"","meta":{"pb_show_title":"","pb_short_title":"","pb_subtitle":"","pb_authors":[],"pb_section_license":""},"chapter-type":[49],"contributor":[],"license":[],"class_list":["post-69","chapter","type-chapter","status-publish","hentry","chapter-type-numberless"],"part":63,"_links":{"self":[{"href":"https:\/\/openstudio.pub\/techwriting\/wp-json\/pressbooks\/v2\/chapters\/69","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/openstudio.pub\/techwriting\/wp-json\/pressbooks\/v2\/chapters"}],"about":[{"href":"https:\/\/openstudio.pub\/techwriting\/wp-json\/wp\/v2\/types\/chapter"}],"author":[{"embeddable":true,"href":"https:\/\/openstudio.pub\/techwriting\/wp-json\/wp\/v2\/users\/1"}],"version-history":[{"count":1,"href":"https:\/\/openstudio.pub\/techwriting\/wp-json\/pressbooks\/v2\/chapters\/69\/revisions"}],"predecessor-version":[{"id":70,"href":"https:\/\/openstudio.pub\/techwriting\/wp-json\/pressbooks\/v2\/chapters\/69\/revisions\/70"}],"part":[{"href":"https:\/\/openstudio.pub\/techwriting\/wp-json\/pressbooks\/v2\/parts\/63"}],"metadata":[{"href":"https:\/\/openstudio.pub\/techwriting\/wp-json\/pressbooks\/v2\/chapters\/69\/metadata\/"}],"wp:attachment":[{"href":"https:\/\/openstudio.pub\/techwriting\/wp-json\/wp\/v2\/media?parent=69"}],"wp:term":[{"taxonomy":"chapter-type","embeddable":true,"href":"https:\/\/openstudio.pub\/techwriting\/wp-json\/pressbooks\/v2\/chapter-type?post=69"},{"taxonomy":"contributor","embeddable":true,"href":"https:\/\/openstudio.pub\/techwriting\/wp-json\/wp\/v2\/contributor?post=69"},{"taxonomy":"license","embeddable":true,"href":"https:\/\/openstudio.pub\/techwriting\/wp-json\/wp\/v2\/license?post=69"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}